BitFlock on WHS 2011 HP Microserver

Comments

• Ogre

  September 2011 Member

  I'm running it on a WHS2011 box and I've had no issues.

  Share on Twitter
• Alex

  September 2011 Covecube

  I just tried bitflock on my HP Microserver running WHS 2011 and it seems to crash my system when it gets to 20% scanning. Server seems to reboot, which is a bit of a pain.

  Could be a storage driver incompatibility. Do you know what storage chipsets / controllers are on that server? 

  Share on Twitter
• cocksy_boy

  September 2011 Member

  Um not right sure off the top of my head - I'll have a look and post back.  I've not installed any additional drivers  either - just the ones that WHS 2011 automatically installed, so this might be an issue, i guess?

  Share on Twitter
• cocksy_boy

  September 2011 Member

  OK, just got this from the HP website:

  
  

  Processor Dual-Core Processor

  AMD Athlon II Processor Model NEO N36L (1.30 GHz, 15W, 2MB)

  Cache Memory 2x 1MB Level 2 cache

  Chipset AMD RS785E/SB820M

  Memory Protection ECC

  Memory Type PC3-10600E unbuffered DDR3 ECC operating at 800MHz

  Standard 1GB (1x1GB)

  Maximum 8 GB

  Network Controller Embedded NC107i PCI Express Gigabit Ethernet Server Adapter

  
  

  Is that what you were after?!

  Share on Twitter
• Alex

  September 2011 Covecube

  Yes, that's helpful. If you could get a dump from the crash, that would be great.

  
  

  You can use the DrivePool dump submission page:

  http://wiki.covecube.com/StableBit_DrivePool_System_Crashes

  
  

  Just make a note that it's for BitFlock.

  Share on Twitter
• cocksy_boy

  September 2011 Member

  hmmmm - settings are right but there doesn't appear to be a memory.dmp files. will check again tomorrow, as I'm cream-crackered and have to sleep now!

  Share on Twitter
• cocksy_boy

  April 2012 Member

  Hi Alex,

  
  

  I know this has been dead for ages, but I'm still not having any luck getting BitFlock to run on my WHS 2011 HP Microserver.  There also appears to be no memory.dmp file either - my windows settings are as per the DrivePool wiki page (except I have the automatically restart box ticked under system failure).  Any ideas? Cheers!

  Share on Twitter
• m0t0k0

  September 2012 Member

  
  

  I know this is old but just so you know I have the same hardware as you and installed BitFlock today no problems

  
  

  Make sure you server drivers are installed from here

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdHome/?sp4ts.oid=5037569&spf_p.tpst=psiSwdMain&spf_p.prp_psiSwdMain=wsrp-navigationalState=lang%3Den%7Ccc%3DUS%7CprodNameId%3D5037569%7CprodSeriesId%3D4248009%7CswLang%3D8%7CswEnvOID%3D4064%7Caction%3DlistDriver&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  Share on Twitter
• cocksy_boy

  October 2012 Member

  Thanks M0t0k0- I'll take at look at that and makes sure I'm running the most up to date drivers.

  Share on Twitter
• bendo

  April 2013 Member

  Hey cocksy_boy, did you ever resolve this? Thanks.

  Share on Twitter